Categories
Shop by Price
Vendors
Join our Newsletter
Subtotal: $0.00
Blog Tags

> Lab Scopes Accessories > 15-inch WyzeProbe for Secondary Ignition and COP

 

15-inch WyzeProbe for Secondary Ignition and COP

AES#:
AW-15
 
$139.00
Qty:
 
California Residents: Proposition 65 Warning
 
 
 
Eligible for FREE Ground Shipping(Eligible for FREE Ground Shipping)
Description
More Info
Video

BACKORDER! We hope to have more of these in mid-December.
 

Scope each COP cylinder, one at a time, and quickly with the WyzeProbe!
This 15-inch probe makes it easier to access the coils.

Works on all labscopes! Industrial and automotive.

Test lead sold separately, see below.

Does more than just COP
* Superimpose secondary ignition patterns on conventional ignition by simply placing probe on the ignition coil or coil wire.
* Superimpose secondary ignition patterns on HEI (Coil-in-Cap) ignition, by simply placing probe on distributor cap center position.

Does more than just Secondary Ignition
* Alternator diode pattern: place WyzeProbe tip on rear (ground) case of alternator. Instead of fighting to get to the positive output terminal of alternator.
* Injector on time: provides a quick way to verify on time and mechanical problems on some injectors used with with COP ignition.

* works on most coil on plug systems.
* Faster than scoping the primary!
* Find misfires that don't set trouble codes without scraping your knuckles or getting dirty.
* Fully shielded to probe tip.
* Capacitive protected to avoid damage to your test equipment.
* Works on all labscopes!
* Works with Snap-on Vantage (ignition patterns only).
* No batteries required!
Test lead sold separately, see below.

Contents
* 15-inch WyzeProbe for Secondary Ignition and COP 
 

Test Leads
The WyzeProbe can be used with practically any oscilliscope. Select the the appropriate test lead to to connect the probe to your scope:
- for scopes with BNC inputs (Pico, OTC, Interro)
- for scopes with Banana inputs (Snap-on, UEI)

 

 

Screen Capture from a Snap-on VERUS

The WyzeProbe can also be used with the Snap-on VERUS. This capture is from a 1998 Nissan with COP before and after.

 
 
 

Screen Capture from a Snap-on MODIS

The WyzeProbe provides a quick way to check secondary ignition with the Snap-on MODIS.

 

The WyzeProbe does not exactly match the input impedance of the MODIS. That means the signal is not a perfect representation of the signal. However, as you can see in this screen capture, it is close enough to evaluate the signal properly.

 

The probe also works with the Snap-on VantagePro, the attenuations are not exact but close enough to evaluate the signal properly.

 

Works on all labscopes! Industrial and automotive.

 
 
 

Screen Capture from a Fluke 98

The WyzeProbe provides a quick way to check secondary ignition with the Fluke 98 and other Fluke ScopeMeters.

 

This screen is from a 4.7L Jeep COP.

 

Works on all labscopes! Industrial and automotive.

 
 
 

Article

Coil on Plug Ignition: The Wired Differences

 

The July 2011 issue of Underhood Service includes an article by Matt Dixon, Assistant Professor, SIU Carbondale. 

 

He used the WyzeProbe with a PicoScope to obtain the secondary signals used for the article.

 
 
 
 

 

 

ScannerDanner uses the AutoWyze with a Snap-on scope on a 2002 Chrysler Town and Country with a waste spark system with code P0302 Engine Misfire.

 

 

 

Supporting our community

Banner Assurance iATN We are a Proud Friend of the NACAT Education Foundation ASE AESwave Ascca AESwave KivaAESwave IAP